Djordje VUKELIC, Janko HODOLIC, Branko TADIC – SERBIA

Tone VRECIC, Peter KOGEJ – SLOVENIA

DEVELOPMENT OF SOFTWARE FOR STATISTICAL PROCESS CONTROL

Angel ZUMBILEV – BULGARIA 

ABOUT THE INFLUENCE OF HEAT TREATMENT OVER THE RESISTANCE AGAINST FRAGILE DESTRUCTION OF BH21 STEEL

jános GYEVIKI, József SÁROSI, Tamás ENDRŐDY,

Endre FORGÁCS, Péter TOMÁN – HUNGARY

LabVIEW Based Position Control for a Pneumatic Cylinder

D. RAJENTHIRAKUMAR, G. CHANDRAMOHAN, P. R. THYLA – India

THE FEM SIMULATION OF TUBE HYDROFORMING (THF) OF THE SUPER ALLOY

Abdelnaser Omran, Hamidi Abdul Aziz – Malaysia

A REVIEW OF HEAVY METAL POLLUTION AND POTENTIAL REMOVAL TECHNIQUES IN MALAYSIA

Elma EKINOVIC, Vlatko DOLECEK,

Nedim HODZIC – BOSNIA  & HERZEGOVINA

Slavko DOLINSEK – SLOVENIA

EXPERIMENTAL VERIFICATION OF AN APPROXIMATE TECHNIQUE FOR DAMAGE IDENTIFICATION IN BEAMS USING NONLINEAR REGRESSION ANALYSIS OF BENDING FREQUENCY CHANGES

R. M. Patel, G. M. Deheri, P. A. Vadher – India

MAGNETIC FLUID BASED SQUEEZE FILM BETWEEN ANNULAR PLATES AND TRANSVERSE SURFACE ROUGHNESS EFFECT

Jaromir Audy – Australia 

Machinability Characteristics of Cu-Sn Work-piece Materials: An Experimental Study

Jozef PETRÍK, Pavol PALFY – SLOVAKIA

THE QUALITY OF VICKERS HARDNESS TESTER CALIBRATION

Ramu Pillalamarri, G. Sasi Bhushana Rao, S. Srinivasa Kumar – INDIA

A Novel Approach for Efficiency Enhancement and Size Miniaturization of UWB Printed Antennas

Agata RADVANSKA – SLOVAKIA

ACCIDENT LOSSES ELIMINATION BY MEANS OF SAFETY PYRAMID ANALYSIS

Salahaldein ALSADEY, Abdelnaser OMRAN, JAYAPRAKASH – Malaysia

STRENGTHENING OF REINFORCED CONCRETE RECTANGULAR COLUMNS WITH GLASS FIBRE REINFORCED POLYMERS

Tamás Besze, Krisztián Horváth – HUNGARY

Analises of the Hungarian polycentric spatial development goals and its achievements concerning the South-Great-Plain Region

Y. M. EL-Barasi, N. A. Ahmaida, M. W. Barrani, 

A. O. El-Amrouni – Libya

Abdelnaser  Omran – Malaysia

POLLUTION OF AGRICULTURAL LANDS BY FERTILIZERS AND PESTICIDES ON EL-GUBBA AND EL-ABRAQ AREA IN LIBYA

Angel ZUMBILEV – BULGARIA

DETERMINING OF RESIDUAL STRESSES IN THE CARBONITRIDED LAYERS X RAY DIFFIRACTION TECHNIQUES

Martin PETRUF, Vladimír MRKVIČKA – CZECH REPUBLIC

LOGISTIC SOLUTION OF CRISIS SITUATIONS

Emília SMINČÁKOVÁ, Ľudmila KOMOROVÁ – SLOVAKIA

KINETIC STUDY OF LEACHING STIBNITE IN SODIUM HYDROXIDE SOLUTION 

Jozef BLAZOVSKÝ – SLOVAKIA

MODELLING AND SIMULATION OF THE INFLUENCE OF BASIC TECHNOLOGICAL PARAMETERS IN EDM MACHINING

Jaroslav Kovalčík, Jiří Čuban – Czech Republic

Long-term Tool Life Tests of American Made Nitride Ceramic Insert’s Used to Turn Grey Cast Iron Work-piece Materials

20.

Stanislav Fabian, Miloš Servátka – SlovaKia

Quantification of the influence of relevant technological parameters on surface roughness by AWJ cutting technology

Mohd Wira Mohd Shafiei, Ilias Said, Radzi Ismail – Malaysia

IS HOUSEBUYERS TOWARD RECYCLE CONSTRUCTION MATERIALS

józsef SÁROSI, János GYEVIKI, Gábor SZABÓ, péter SZENDRŐ – HUNGARY

LABORATORY INVESTIGATIONS OF FLUID MUSCLES

István Péter Szabó – Hungary

Efficient Energy Storage in PCM Solar Tank

N. A. Chowdhury, Mohammed Anayet Ullah Patwari – Bangladesh

DESIGN A BALL BURNISHING ROLLING TOOL AND INVESIGATING ITS EFFECT ON SURFACE QUALITY

Vania Rangelova, Antonia Pandelova,

Nikolay Stoyanov – BULGARIA

Inhibitor multienzyme biosensor system in dynamic mode

N. Kapilan, T.P. Ashok Babu,  R.P. – INDIA

PERFORMANCE AND EMISSIONS OF A DUAL FUEL OPERATED AGRICULTURAL DIESEL ENGINE

K. Klimentov – Bulgaria

Analysis of results from balance investigations of centrifugal pumps 6E20 and 6E32 with air-water two-phase flow performance

R. Muthucumaraswamy, M. Muralidharan – INDIA

RADIATIVE HEAT TRANSFER EFFECTS ON LINEARLY ACCELERATED ISOTHERMAL VERTICAL PLATE WITH MASS DIFFUSION

Rosa Beatriz Orellana, Gregorio Perichinsky,

Luís Ángel Plastino – Argentina

Computational Taxonomy for Identification of "Moving Groups". Applied to Open Clusters

30.

V. RAJESH,  S. Vijaya KUMAR VARMA – INDIA

CHEMICAL REACTION EFFECTS ON FREE CONVECTION FLOW PAST AN EXPONENTIALLY ACCELERATED VERTICAL PLATE

Toni UZUNOV, Stoyan STOYKOV, Georgi KENAROV – Bulgaria

INVESTIGATION METHODS OF THE INFLUENCE OF THE TIMES IN TRANSITIONAL PROCESSES ON THE DYNAMIC LOAD FOR LIFTING DEVICE

Zoran PANDILOV, Vladimir DUKOVSKI – Macedonia

SURVEY OF THE DOMINANT ERROR TYPES AT PARALLEL KINEMATICS MACHINE TOOLS

RAMU  M., PRABHU Raja V., THYLA P. R., GUNASEELAN M. – INDIA

APPLICATION OF METAMODELS IN DESIGN OPTIMIZATION OF COMPLEX STRUCTURES

Ashu GUPTA, Rajesh VERMA, Kawaljeet SINGH – India

A Critical Evaluation and Comparison of Four Manufacturing Simulators using Analytic Hierarchy Process

Mohd Wira Mohd SHAFIEI, Fanny S.S. FOO,

Ilias SAID, Abdelnaser OMRAN – MALAYSIA

MALACCA HOUSE BUYERS’ HOUSING PREFERENCES IN MALAYSIAN NEW RESIDENTIAL MARKET 

Saad BAKKALI, Mahacine AMRANI – Morocco

modelling phosphates “disturbances” DEPTH using analytical signal RESPONSES of geoelectrical resistivity data (Sidi Chennane, Morocco): PRELIMINARY RESULTS

37.

Jarmila Oravcová, Peter Košťál, Eva Riečičiarová – SLOVAKIA

ACTIVE PARTS OF CLAMPING DEVICES

38.

Tamás BESZE – HUNGARY

THE PRACTICE AND EFFECT OF THE POLICENTRIC SPATIAL DEVELOPMENT OF THE EUROPEAN UNION ON THE RELATION SYSTEM OF THE DKMT (DUNA-KÖRÖS-MAROS-TISZA) REGION

Tome VIII (year 2010) - Fascicule 1